Peugeot 3008 Key Fob Problems The mid-sized SUV from Peugeot, the 3008, has lots of positive points It's stylish, handles well, and has a large boot Can it compete in the most crowded segment of the market, perhaps If your Peugeot key fob isn't functioning, it might have been exposed to clean tap water or soapy water You may need to take off the battery, clean it with isopropyl ethanol or electronic cleaner Dead coin battery Peugeot key fobs are powered by the coin-sized battery The power utilized to operate the remote locking system and other functions The battery is limited in lifespan and can wear after years of usage Voltage testing is an easy method of determining if the battery is not working properly Multimeters can be used to measure voltage between the poles that are plus and minus of the battery This test will determine if the battery is dead If you've been using your Peugeot 3008 for a while, and your key fobs stopped functioning, it could be a problem with the receiver module The receiver module is responsible for receiving radio frequency signals sent by the key fobs, and then sending them to car systems If the receiver module is in issues, it will not be able to transmit commands to the other modules in the car The presence of moisture or sweat on the circuit board is another typical reason for an inoperable key fob This can lead to short circuits which drain the battery and disable the remote locking feature of the key fob If this is the case you need to bring your key fob to a specialist in chip level repairs Water damage Water damage can be a concern when you drop your keyfob into the swimming water, washed it, or left it out in the rain Water is a good conductor, and it can also short out parts of the circuit board It can also cause corrosion to metal traces on the key fob as well as other components A wet circuit can cause a battery to lose its charge If you have an extra key fob use it to lock or unlock your Peugeot 3008 to eliminate the possibility that a dead coin battery is the root of the problem Interference signals can also cause your key fob to stop working properly They interfere with the signal generated by the receiver module These signals could come from a wide range of sources that include radio transmitters near by If you hear sloshing noises emanating from your Peugeot 3008 when you drive, this is likely caused by a blocked condensate drain from the evaporator You can test this by blowing compressed air into the drain holes underneath your door You can also use flexible metal wire to move drain holes around to get rid of any dirt accumulated Air pockets can be indicated by sloshing noises Receiver module that is defective The receiver module inside a Peugeot 3008 key fob is responsible to transmit the remote keyless system signal from the key fob to the car's receiver If the receiver module is damaged, it may hinder the car's ability to recognize the key fob This issue can be caused by an unresponsive battery or water damage It could also be caused by interference from electronic devices operating at the same frequency In these instances the car might display the message "card not detected" on the display Luckily, there are a number of ways to fix this problem You can try replacing the battery or reprogram the key fob You can also utilize a spare key start the car However, if https//wwwthekeylabcouk/peugeot-car-keys/ fob isn't functioning after all these steps, it could have a chip malfunctioning The best way to determine whether the key fob has an issue with its chip is to take it off and clean it with a paper towel and rubbing alcohol If the chip is damaged it is recommended to purchase a new one The FB Series enclosures come with an accessory for battery holders for coin cells that fits the most popular kinds of key fob batteries These enclosures can be customized by using digital printing and CNC-machined cutouts If your key fob has been exposed to dirty or salty tap water, your chip may be contaminated and requires to be cleaned Faulty keyless entry system If you get "card not detected" This signifies that your car is unable to receive an alert from your key fob This could be due to several factors, including the battery being weak or dead The issue is usually solved by pressing the start button on the key fob In some cases you may require taking the keyfob to an Peugeot dealer for repairs The battery test is the first step in troubleshooting an Peugeot 3008 keyfob, which is unable to unlock or lock doors Batteries are often the main reason for a fob that is malfunctioning, but there are other factors that could contribute to this issue as well This includes worn buttons and water damage If you've recently experienced the Peugeot key fob exposed to clean tap water, it's a good idea remove the battery and dry the electronic components with paper towel You can also try isopropyl alcohol or an appropriate cleaner for this It is best to change the fob if it has been exposed salt water or soapy water If your key fob is still not working, you can try to reset it by disconnection of the battery that is 12 volts for about 15 minutes Then, reconnect the negative cable first, then followed by the positive cable