uPVC Window Repair While uPVC windows are durable and resistant to harsh weather conditions they are not immune to issues that require fixing Luckily these problems can be repaired easily at only a fraction of the cost of replacing a window A common problem is that windows become difficult to open because its hinges are stiff Fortunately, this problem can be easily solved by lubricating hinges with something like WD-40 Broken or cracked glass Glass is everywhere in our homes on doors, windows and tables in stoves and microwaves even in frames for pictures A good baseball hit or a rough-housing session with friends could cause cracks in your windows which need to be fixed promptly before they get any worse Luckily, these types of cracks are very easy to repair without the need to replace your window glass or frame First, clean out the area using a moist cloth to get rid of any dirt, dust or fingerprints Use a small amount of epoxy to seal the crack Let the epoxy dry completely before moving your window again This is a straightforward repair that can save you the expense of replacing your uPVC windows The window gasket can also be brittle or split from the frame This will lead to a loss of insulation and also the introduction of cold air, or even water into your home It is possible to fix this by using a flat knife, such as a credit-card, to separate the gasket from the window frame If you have some time, you can add a bit more epoxy to the crack, so that it looks like it never existed If the crack is deeper than you can reach it with your fingers, you can use a piece of tape to shield the area from further damage You could also use clear nail polish to fill in the crack to stop the crack from expanding It is important to act quickly upon noticing the crack In the event that you don't, it will spread and become more difficult to fix If you are looking for a more permanent solution consider using uPVC epoxy to repair your broken or cracked glass This is the most time consuming of all the alternatives but it will provide the most efficient results in terms durability and appearance Follow the manufacturer's instructions for applying the epoxy and make sure to clean the surface with an acetone-soaked rag once it is fully dried Water Leaks Upvc windows are extremely durable, but they require some maintenance and care If they're not maintained properly various issues could develop These issues could range from water leaks around the frame, to condensation within the glass units A good uPVC window repair expert can help identify the issue and fix it They can also provide tips on how to avoid repeating the issue in the future Leaking uPVC Windows are a major problem that should be fixed as soon as they begin to occur If the issue isn't taken care of, it could lead to major damp problems within your home This could lead to costly repairs and an increase in energy efficiency A leaky uPVC can be fixed with a patch The sealant is sprayed inside the window to prevent water from entering the house through the damaged area Cloudy or misty double-glazed units indicate that the seal between the panes of glass has failed https//wwwfccgov/fcc-bin/byehttps//wwwrepairmywindowsanddoorscouk/camdentown-windowrepair/ could be caused by a variety of reasons, including wear and tear, age, weather conditions or simply aging One way to avoid this is by having your windows cleaned regularly It is recommended to wash windows at least twice a year with a soft white cloth that has been soaked in warm water and liquid soap It's important to avoid using any colored cloths since they can leave dye staining on the plastic Solvent PVC cleaner is the best way to remove stubborn stains It can be purchased from any hardware store and is easy to apply Be sure to clean the window frames in a shaded location away from direct sunlight to prevent any streaking The Locks and hinges are faulty and faulty Over time, a window hinge can become damaged or bent This can lead to a gap forming in the frame, which can let draughts in and decrease energy efficiency A draught can also make your home feel cold and uncomfortable, and increase your heating bills A uPVC window's gap is an issue that can be fixed easily A uPVC window repair expert can identify the problem and fix it for you Usually a small hole can be repaired using carpenter's glue and a wooden dowel inserted into the gap The dowel should be placed in such a way that it is flush with the hinge leaf and has a smooth surface The adhesive of a carpenter is spread on the dowel, and then tapped into position After it has dried and cured, a screw is put in to secure the hinge UPVC window hinges and locks may become stiff to open and shut over time due to general wear and tear, or due to blockages caused by dirt and debris They must be cleaned and checked frequently to ensure that they're working properly Use WD-40 to ensure that moving parts remain in working order It is recommended to wash UPVC windows at least twice a year The damp cloth is dipped into the mixture of mild detergent and water The areas around the corners of the window need to be cleaned more frequently in order to avoid build up of dirt and corrosion The handle of a uPVC window may also become stiff to open or close This could be because of the handle falling or it could be caused by issues with the locking system This is a quick and easy repair that can be completed by the homeowner if they follow some easy steps A damaged lock poses a security risk, as it could make your home vulnerable to burglars A damaged lock could cause your uPVC window or door difficult to open, which could be an inconvenience for you A new handle or a adjustment of the multipoint locking mechanism may be required if this happens to be the situation Stuck Handle It is quite annoying when the window handle made of upvc is stuck, particularly when you try to open the window and it requires lots of force, or it doesn't even open at all This is usually caused by the wire that is in the handle holder and has become rough By simply removing the handle and having a look at the wire, you can often smooth out the rough area and fix the issue You can also address this issue by applying graphite or paraffin on the pole sliders This will allow the handle to move upwards and downwards It is also a good time to clean your handle as it will stop any future issues If the issue is with the button itself, this can be repaired by using superglue on it Make sure the superglue is completely dry prior to attempting to use it again If the handle is damaged or broken it can be fixed by purchasing a new one and screwing it in the right place It is easy to repair this yourself if you have the appropriate tools