Upvc Door Lock Replacement It's simple to change the lock on your uPVC doors It's cheaper than contacting locksmiths to do it for you, and will keep your door safe from serious damage should you attempt to open the cylinder without a key The majority of doors in the home, including French and patio doors are equipped with uPVC locks Everest is the most well-known manufacturer of lock Cylinders Fixing the Cylinder The cylinder is the part of the lock that accepts and turns the key It has tumblers that are aligned when the right key is placed Changing the cylinder is an easy and efficient way to enhance your uPVC door's security However, it is a job best left to a professional Making the change by yourself could cause damage to your door and give you more issues in the end A locksmith can assist with this by taking out the old cylinder and replacing it with a new one They can also provide advice on which cylinder is best for your door They will also ensure that the lock is correctly fitted and secure You might require a replacement for your cylinder due to a variety of reasons, such as after a break-in or the move of your home You might also want to improve the level of security at your home or to meet the requirements of insurance A professional locksmith will provide you with a variety of uPVC locks that will meet your needs To replace your cylinder, need a screwdriver and a set of screw extractors You can purchase these tools at most hardware stores and on the internet Begin by loosening the screws that secure the face plate and door handle The next step is to open the front door so you can reach the inside of the door frame and the faceplate of the lock You can then remove the screws and save them in a safe location Once you have removed the faceplate, you can remove the cylinder Inject the key into the hole and rotate it right or left about 10 degrees This will loosen the cylinder, allowing you to remove it from the hole Check the key to confirm that it is working correctly If the key isn't turning, then you might want to lubricate the key with a little bit of oil or grease Most hardware stores offer lubricant and many locksmiths also stock it This can help you get your door to unlock without much hassle and mess Fixing the Sticking Mechanism The upvc lock mechanism could get stuck or become difficult to secure and close In these situations an a bit of troubleshooting may help you solve the issue without having to replace the entire mechanism You can start by inspecting the mechanism to find out what is causing it to stick It could be as simple as hinges aren't being lubricated or it could be something more serious like a broken gearbox You can also try to lubricate the locks in your home by using common household items like WD40 This will ensure they are in good shape and extend their life Make use of a soft-bristled tooth brush to remove any dirt and debris that has accumulated inside the lock Keep your upvc lock oily and tightened so that they last longer This will also reduce the force needed to open and shut them If you're facing a lock problem It is best to consult a specialist rather than trying to fix the problem yourself It's not worth the risk of damage to your uPVC door or causing further problems with the locking mechanism in the future It's worth paying a little more for the assurance that the work will be carried out professionally by someone who has years of experience If you plan to change a uPVC door lock yourself it is recommended to follow a step-by-step guide to make sure you are aware of the procedure or watch a video You're more likely to cause harm if you don't You may even damage the cylinder or the door handle Fixing https//wwwrepairmywindowsanddoorscouk/ilford-window-lock-repairs-near-me/ that is loose Many people replace their uPVC handles for many reasons, such as to improve security or to comply with insurance requirements It is important to select replacement handles that are of high-quality to avoid problems like the handle becoming floppy If the uPVC handle is loose, then it's likely that the mechanism must be tightened This is usually a simple process that can be done by yourself, but if not confident with DIY, you should call in a professional locksmith to do the job for you The first step is to take off the handle, and then locate the screw that holds it in the first place Once you've located it tighten the screw using the screwdriver It might require a few times to get the screw to line up correctly, but be careful not to over-tighten it or cross-thread it Once the screw has been secured, you can reinstall the handle to ensure that it is working properly Alternatively, you can replace the entire handle plate instead of only the screw Depending on the lock type, you might need to use different screws for this task After you've replaced the handle, check that it is lined up with the keyhole and it's not sticking or moving when you turn it It is also possible to grease it to ensure it does not get stuck in an unsuitable position If the problem persists you should seek out a professional double-glazing repair service It can be stressful to replace your damaged or old locks, whether you are doing it out of choice or out of necessity It is therefore advisable to hire an experienced locksmith to complete the job for you so that it is completed to the highest standards and any additional problems are avoided They'll also be able to advise you on the best locks that best suit your home Whether you're looking for a Sold Secure SS301 SS301 approved set or a 2 Kitemark, they can help Fixing the damaged Gearbox If you're experiencing issues with your uPVC door, it could be time to think about replacing the lock on your upvc door Locksmiths can easily fix the issue, and it isn't as severe as you might think Be aware that replacing the entire mechanism can be costly, so it is not something you'd prefer to do at home To begin, it's important to determine what kind of door you have in order that you can buy the correct parts for the replacement of a door lock made of upvc To replace the lock, you will need to take a measurement of your lock to determine the model This process will be much easier if you have the original lock that was installed on your door to refer to It is also important to make sure you have the right tools for a upvc door lock replacement, which will include screwdrivers, a drill, and a Hammer Using the correct tools will ensure that you don't end up damaging your door while trying to repair it Once you have the tools, you should carefully follow the instructions that are provided by the manufacturer so that you can install the lock correctly Once you have received the replacement, you'll be required to test it, and then make any necessary adjustments This will ensure that the replacement works well and is able to be used in the way you intended If you are not sure how to go about this it's an ideal idea to seek out an expert If you notice that the upvc door handle is loose or floppy, it could be an indication of an issue If so, the issue is likely to be with the 'barrel' portion of your lock If this portion of the lock is loose, you will have problems with your door handle This is the area where the key's indent located To tighten the handle, find the screw that holds the barrel of your lock and tighten it with a screwdriver This will tighten the handle and solve the issue of a loose handle Although it may sound intimidating at first to remove a uPVC door in order to replace the lock cylinder or gearbox The modular design of these doors makes it easy for the majority of people to complete this task on their own for less than the cost to employ a locksmith