Car Locks Repair Typically, a locksmith for cars will be able to work with both manual and power door locks Manual lock problems may be more common but they can be frustrating WD-40 is a great oil to use in the winter It will help to displace moisture and prevent it from freezing inside the keyhole Door Lock Cylinder Replacement It's a good idea replace the door lock's cylinders as soon as possible in the event that you lose your car keys, or suspect that someone else might have This will ensure that you're the only person who has the ability to open your vehicle and keep other unauthorized people out of it It can be difficult to replace a door lock cylinder, as it typically requires removing the door's interior It is not something that the majority of people would prefer to tackle on their own It can be dangerous in the wrong way First, the lock cylinder must be removed from the handle You will have to locate the screw on the top of the housing usually upper right corner You may find it hidden beneath plastic pieces or just barely visible If you are unable to locate it, remove any trim panels blocking your view Then, use a screwdriver or awl or a small screwdriver to open the lock cylinder retaining tab and take the cylinder out of the housing Once you have the cylinder removed and reassembled, there are some things that must be done to prepare it to use The keyway should be cleaned to remove dirt and grease The cylinder needs to be lubricated so that it is not stuck in the lock The most efficient method to accomplish this is to use brake cleaner, which can clean and lubricate the lock components of the cylinder After cleaning you can take off the 10mm bolt that connects the handle to the housing of the cylinder using a screwdriver You can then install the new cylinder and use it with your original key It is a good idea to get a cylinder that matches the brand and model of the one you have since it will be more likely to fit correctly and seal securely Test the door after installation to confirm that the lock functions properly and that it is closed securely Door Lock Cylinder Repair The lock cylinder is the component of your car door that keys fit into to unlock or secure the door If the key is stuck inside the lock or you are having difficulty turning it, this could indicate that the door cylinder needs to be replaced It's usually near the door handle, although some vehicles have them hidden behind an aluminum piece When you turn the key, the pins inside the cylinder align with the cuts on the key head and allow you to move the lock to unlock the car door If you have a cylinder that is mounted on the surface remove the faceplate from the door handle Unscrew any or all setscrews for the cylinder When the screw is loose You can turn the cylinder so that you can take it out of the door Place the screws in a bag, or in a safe location to replace them in the future Then put the key in the lock and make sure the tumblers and pins are movable If the cylinder is stuck or you feel or hear a click, it's time to replace it You can buy new cylinders at any auto parts shop, but you will have to know your vehicle's model and make prior to you shop You can also contact a locksmith to replace the door cylinder They'll be able match the new unit to the key you have already, so that you can use the original lock The most common issue is that the cylinder will not rotate when you turn the key This could be due corrosion or dirt that has accumulated, which prevents the cylinder from turning freely It is easy to fix this problem by lubricating your mechanism You can apply brake cleaner to rid your cylinder of any rust and grime or commercial lubricant such as white grease This method only works on a cylinder that is jammed It will not fix any other problems Door Lock Repair A door lock can be stuck due to rust, dirt or other debris This can be resolved by spraying WD-40 over the mechanism This will clear the mechanism, and stop it from happening again in the future If you're unable to get the lock to turn, try wiggle the rod up and down with needle-nose pliers If this doesn't work you, you must contact locksmiths to replace the lock A misalignment issue is another frequent issue with doorlocks This could make the lock difficult to use and poses a security risk because it makes the door easier to bypass in a break-in attempt A locksmith should be called to address this issue, however you can usually fix the problem yourself Begin by inspecting the lock to determine what is causing it to stop working properly If the issue is due to a misaligned strike plate, or deadbolt, tighten the screws holding these items Then, move the strike plate and bolt to ensure they are aligned with the door frame A little graphite can be used to solve the issue when the key is unable to insert or turn You can apply the graphite to the key by either squeezing it from a tube, or dusting it on the key with a spare After that, you can insert the key and turn it several times to incorporate the graphite into the mechanism If this does not work, take the knob off and inspect the spindle it may be worn out The process of removing a door handle or panel varies depending on the vehicle, but it is generally the same After removing the panel, you'll be required to locate the set screws holding the lock cylinder These are usually located in the middle of the panel or on the inside of the door handle, depending on the make and model Remove the screws and then carefully align the cylinder with the keyway It is possible to damage the components if tightening too tightly the screws Door Lock Replacement Replace your lock if it's worn or looks a little old It will give you a new look It's a fairly simple procedure that can be done at home by following just a few steps Just be sure to make sure you examine the deadbolt and latch to be able to ensure that your new locks are properly set Begin by taking off the screws that secure the knob's inside plate to the door Take the knob and latch out If the interior plate is decorative and does not have screws, you can carefully pry it up with the screwdriver The plate could be secured by pins or snap off the edge Once the plate has been removed, it is easy to take out the deadbolt and latch Now is the time to put the new plates for your lock in place Make sure that the inside and exterior plates are lined up over the deadbolt hole on the jamb for the door and that the long spindle of metal from the lock cylinder mechanism moving through both holes Once the plates are set, you can thread the screws through the holes to secure the plates together If the plate doesn't have any screw holes, then you can simply slide it on the latch Use the screws included in the lock kit you purchased instead of the ones you already have Instead make https//wwwg28carkeyscouk/car-door-lock-repair-near-me/ of the screws that came with your new lock kit If you don't have the correct size screws, visit a hardware or home improvement shop and purchase some that match the rest of the hardware used on your new door lock Make sure that the new latch plates and deadbolt are the same length as the original ones and that they are centered over the latch hole of the door jamb Once all the parts are in place then tighten the screws You can now test the deadbolt and latch using your key If the key isn't turning then it's time to contact a locksmith