Peugeot 208 Key Replacement It is recommended to leave the replacement of Peugeot keys for 208 to auto locksmiths that have the necessary equipment and technical skills They will be able to create and program new keys faster than a dealership would and at a lesser cost A dead battery for your coin is most likely to blame the reason your key-fob stops locking or unlocking the doors There are many other reasons why the key may be malfunctioning Dead Coin Battery A dead coin battery can hinder your Peugeot 208 from locking or unlocking and cannot start the engine If this is the case, you'll have to apply the backup starting technique that is described in the owner's manual of your vehicle Another reason why your 208 might not be starting is that the spark plugs have been damaged Spark plugs are what ignite the fuel to start the engine They have a limited lifespan They'll eventually degrade if they aren't used frequently enough There is a simple solution to this problem Verify the voltage of your battery using a multimeter If it's lower than 115 volts then you must replace it If the battery has corrosion, it is important to clean its contacts This can be accomplished by taking off the rubber covers from the two battery terminals, and then using a wirebrush to remove any corroded battery parts After that, you need to connect the positive and negative pole cables Water Damage If your 208 won't turn on and the battery isn't empty, you must ensure that the spark plugs work https//wwwg28carkeyscouk/peugeot-car-key-replacements-near-me/ could be that they're dirty, causing them not to spark This can be fixed by cleaning the spark plugs in a workshop Peugeot cars are equipped with a key with a transponder compatible with the immobiliser This ensures that only the right key is able to start the engine If the chip inside the Peugeot key is damaged, it won't transmit the correct signal to the vehicle Water damage is a frequent cause of this problem This is a common issue in more cold climates where the car has been exposed to snow or rain In this situation, contact an experienced locksmith who has the required tools and equipment to change the key's programming They'll also have the latest technology and equipment needed to make the Peugeot smart key The process should take no more than 15 minutes Contacts for the battery that are defective Peugeot replaced the transponder chips with a brand new model that is based on electronic components mounted on a circuitboard The new system is great in its initial state, but the circuit boards begin to degrade with time and cease to function properly This can prevent the immobiliser from working, so your vehicle won't start Contact a Peugeot specialist, or a locksmith if this is the case A common issue is when the battery of the key fob starts to fail This causes the blade of the key to stop feeding into the lock A locksmith for cars will replace the battery, and then cut a new key blade for you This is a simple solution Faulty Receiver Module If your Peugeot key fob has stopped working after dropping it on the ground, being exposed to a sudden downpour or accidently washing it or washing it, it could be due to a defective receiver module The receiver module is responsible for transmitting radio frequency to the onboard computer that manages the central locking system of your Peugeot vehicle The rubber seals on the key fob prevent water from getting to the electronic chip The chip can be damaged by water when exposed to water for a prolonged period of period of The high salt content of the pool or ocean water can cause damage to the key fob if it is submerged The module will need to be replaced if your Peugeot spare key does not work anymore This is only performed by a professional auto locksmith or Peugeot specialist Peugeot keys unlike other automobiles, are protected by an immobilizer system This requires the proper code to begin the car This is the reason that you should only rely on the Peugeot locksmith to create and program a replacement Computers with faulty on-board computers The computer on the board of your Peugeot is responsible for a variety of the systems within your car, from airbags to power windows If something goes wrong with these systems, they will usually display a code that indicates the issue The code will be stored in the system until the issue is resolved This can often mean that the on-board computers to be replaced The most typical reason for the warning light for the airbag to come on is corroded or loose connections in the sensor This can be caused by wear and tear, aging, or exposure to salt and moisture It is essential to have this issue addressed as quickly as you can, since an airbag that is malfunctioning can be dangerous in the event of an accident If you find an error message stating that the card is not found on your Peugeot, the key battery inside the key fob could be weak or dead This prevents the key fob from sending a signal that disarms the standard immobilizer in your vehicle Test this by pressing the unlock button on the fob's key and then trying to start your vehicle If this doesn't work it is likely that the battery will need replacing