Saab 93 Key Fob Replacement Saab key fobs with 93 keys can be costly to replace The procedure is easy You will require a flathead screwdriver and some patience Simply insert the screwdriver in the middle of the case and slowly open it open A spare set of keys and fobs is an excellent idea They can prevent you from being stuck or paying towing costs How do you replace a battery Car key fobs that enable and lock your vehicle remotely are powered by a battery which will eventually fail In just a few easy steps, users can replace the battery in their key fob The key fob features two plastic flaps on one side that you need to lift to remove the old battery and then install the new one The replacement battery is a standard CR1632 coin cell, and the process to install it is simple After you have removed the emergency key, you can use the flathead screwdriver on the wood to split the case Do not force the case too much as the electronics are delicate and may be damaged by too much pressure Saab produced some fantastic cars, and many of them still exist in the world today One of the biggest problems with these cars, however, is their ignition keys They're not the most robust, and they may become spongy or loosen in time If an Saab owner loses their sole functioning key, it could be quite costly to buy an additional key at the dealership, since they must replace the entire computer module, and then program it with the new key to convince the car that you're not trying to take it The good thing is that you could save cash by simply replacing the case instead How do you remove the Manual Key Batteries are found in all key fobs used in the process of lock and unlock vehicles They have a limited lifespan If you're like most people, it will eventually go out It's not difficult to replace battery for the key fob that is manual The only difficult part of the process is removing the old battery from the case With a bit of patience and a flathead screwscrewdriver, you can complete the task After you've put in the new battery, it's time to reassemble the entire thing To do this, you'll have to open up the replacement key fob case This can be done by inserting a flathead screwdriver in the slot located in middle of the case Gently move the case until you can remove it If your old keyfob lost its connection with the security system in your vehicle and you need to modify the new keyfob This can be done by following the manual learning procedure to add a new FOB to your 2010 Saab 9-5 This method does not erase previously learned keys however, so you can use the existing FOBs in case they need to be re-programmed To initiate this procedure the FOB that will be programmed must have the mechanical key cut in line with the model of the vehicle How can I change the situation It's a good idea replace both the case and the battery when changing the manual key or the battery The cases are susceptible to wearing out, especially after a lot of use It's simple to change the case of your SAAB 9-3, and you won't need any special tools The first step to change the case is to remove the manual key from the fob This can be accomplished by pressing the SAAB logo and pulling out the manual key The key fob can be sticky at times, and it might take a bit of force to take the key out After you have removed the manual key from the case, you can begin removing the electronic components To accomplish this, you'll need an inexpensive flathead screwdriver You'll need to be careful not to harm the electronics inside, so use care when using your screwdriver Once you've removed all electronics, you can begin taking off the battery Once you've replaced the battery, you can put everything back together in a new case You can buy cases for replacement on the internet at a fairly low cost How to program the New Key All key fobs that allow you to lock and unlock your car remotely use batteries, but they have a limited lifespan It is important that you replace the battery of your key fob every three to four years This is a simple procedure which you can perform at home All you need is patience and an incredibly small screwdriver for phillips screwdrivers The first step is to remove the manual key Press the blue SAAB logo and then pull the emergency key out of the key fob The key should be able to slide out with some force Once you have the key fob in place, you can remove the old battery by gently pushing the screwdriver into the slot located in the middle of the case This will split the case, making it easier to get at the electronic components It is now time to program the key This can be accomplished by following the instructions in this YouTube video by YouTube Cyclone Cyd user This is an excellent video channel that offers instructions on how you can carry out simple maintenance and repair jobs on vehicles Key fobs can be a convenient way to store an extra car key in the event you break or lose your original You can purchase a replacement keyfob from an online store or a local locksmith such as United Locksmith The cost is significantly less than if you bought the key from a dealership https//wwwthekeylabcouk/saab-car-keys/ will charge for the key and then program it into your car