Replacing a Broken Upvc Door Lock Many parts of the upvc lock can malfunction or break They could be damaged by extreme weather conditions or when you accidentally slam or hit the handle too hard A cylinder can be repaired to fix a multi-point locking device and it's fairly inexpensive You can do it yourself for less than locksmith's price The barrel is replaced The barrel is the element of a upvc lock that holds the handle in the right position It is a relatively straightforward process to change the barrel on an upvc door, however it is crucial to follow the proper steps to avoid damaging the door If you aren't sure how to do this you should seek out a professional locksmith or a repair specialist for upvc Firstly, the lock cylinder has to be removed from the door This can be done using a screwdriver A screwdriver with an extended length is ideal, as this will allow you to reach the lock cylinder without having to remove any other parts After the cylinder is removed the barrel can be removed Be sure to note the dimensions of the cylinder prior to purchasing another one Sizes can differ If your lock made of upvc is becoming smoky or difficult to open, it may be time to replace the barrel on your lock This can be achieved by following the steps below Remove the screw that holds the door handles, handle and cylinder Then, carefully remove the handle You can then replace the old barrel with a new one It is important to remember that the screws on a door made of upvc lock are extremely tight and you should always be careful when adjusting them Trying to force them can damage the door, leaving it vulnerable Skipping steps can also result in a smashed screw or a cross-threaded screw, making it impossible to repair the door lock correctly A upvc lock may have different backsets based on the door type A standard upvc door will have a backset of 35mm, while a composite or timber door has a backset of 45mm A locksmith is in a position to assist you in determining the correct backset for your door When replacing the cylinder in your upvc doors It is important to determine its length and the location of the cam The cam is usually located in the middle of the cylinder It can also be found on the faceplate of the cylinder Handle replacement If you've got a damaged door handle made of upvc, it can be very difficult to open and close the door But, this issue can be solved easily by replacing the handle with a new one Handles for replacement are available in many sizes and colors that complement your home's style It's only two screws and a few measures to replace the handle The majority of uPVC doors come with multi-point locking systems This type of lock has many advantages, including increased security These locks can become floppy and cannot lock or turn as they should A loose lock can be a problem since it could allow a burglar with a heavy crowbar to gain entry into your home https//wwwrepairmywindowsanddoorscouk/croydon-window-lock-repairs-near-me/ is why it is essential to replace the damaged handle as soon as possible In the majority of instances, the reason for a broken uPVC door handle is a simple issue with the mechanism The lock can become sloppy as time passes if it's not regularly lubricated This is also a possibility if the weather conditions impact the alignment system Lubricating the cylinder and handle regularly is crucial to ensure that they function well and securely If the handles on your upvc door are damaged, it's crucial to replace them as soon as possible to stop intruders from getting into your home You can find a variety of handles on the market Some are made of stainless steel which is perfect for homes near waterways The stainless steel handles last a long time and are resistant to corrosion To replace the handles made of upvc remove the screw that holds it in place Use a screwdriver and remove the screw Make sure you keep the screws in a safe location as they will be required to install the new handle in Then, find the screw positions on your upvc, and take the measurements for the new handles These measurements include the distance between the centre of the cylinder and the key hole as well as the size of the two fixing screws Once you've got the measurements, you can begin shopping for the correct handle The replacement of the cylinder You can replace the cylinder if your lock is damaged This is the part that receives the key and houses the tumblers You can buy a new lock at any hardware store, or online But, this procedure requires a lot of effort and can harm your door It is recommended to hire a professional locksmith for this task There are a variety of reasons you may require replacing the door lock made of pvc The lock you are using is susceptible to "lock snapping," a technique that allows criminals bypass the normal security mechanisms This can be prevented by purchasing a lock with anti-snap features Replace the barrel on the lock These are small metal rings that fit around the keyhole They make it harder for thieves to open or take locks by lifting the handle and then jiggling the handle upwards These are cheap and easy to install, making them an a great addition to your door made of upvc You can also shield your Upvc door from burglars by putting in hinge bolts Pins are used to secure the hinges and stop them from being pulled off They can be found in home improvement stores and aren't expensive They're especially useful on outward-opening doors since they prevent intruders from forcing the door open Before you attempt to replace your cylinder you should prepare some tools You can remove the screws holding the cylinder using the help of a Phillips screwdriver or a tape measure Then, you can determine the proper measurement of your cylinder before purchasing a replacement There are around 25 different sizes of cylinders It is crucial to accurately measure them The first step is to pull out the screw on the door's faceplate which is holding the lock on the barrel Usually, this screw is distinct from the other screws on the door Once you've removed this screw, you'll be able to remove the lock on the barrel and remove it The new lock cylinder should be inserted into the barrel and turn it to the right to secure it The faceplate is replaced The faceplate of a door lock made of uPVC is the part which connects the handle with the cylinder The faceplate of the door is typically constructed from uPVC and it is fitted with a groove or an escutcheon fitted over it, to keep the locking mechanism in place It is essential to ensure that the faceplate's dimension is in line with the dimensions of the lock you're buying This will ensure that the lock fits correctly and is not too tight or loose Before you buy a faceplate replacement for your door made of upvc make sure you know the dimensions of your current lock This information can be found by looking at the keyhole and then looking for a manufacturer's name on the You can also use a hex key or a screwdriver to pry the faceplate off and examine the mechanism of the lock If the lock is old it might be a good idea to get a new one, which can be an even more secure alternative You might need to replace your door's upvc lock for a variety of reasons It could be that you have recently moved into your home, an earlier tenant hasn't returned your keys, or some part of the mechanism has been damaged It's a simple task that takes less than five minutes to replace the barrel of your lock To determine the size of the cylinder required, first determine the width and height of the square spindle as well as keyhole on your door The measurements should be taken from both sides of the door and recorded in a precise manner You can use a vernier caliper, but you could also employ a ruler Choose a certified anti-snap Cylinder from a reputable security organization These locks have been tested to stop the threat of snapping locks which is a common method of gaining entry through uPVC doors This type of cylinder will provide extra security to your home at a reasonable price Upgrade your uPVC doors by installing hinge bolts These are pins that fit inside the hinges They help to keep the door from being pushed open and are easy to fit They are sold by most hardware stores at a bargain price