Replace Lock on Your UPVC Door Yourself You can change the lock on your door made of Upvc by yourself, as long as you have full access to both sides of the handle's faceplate You'll also need an screwdriver, a long bolt and the key Sometimes, a uPVC device may become stuck due to a lack of lubrication or if there's a problem inside If you know what to do, it's easy to fix Preparing for repairs uPVC door issues can range in their severity It is possible to fix the problem yourself in the event that your uPVC lock is stuck or misaligned However, it is important to ensure that you do not to cause any damage to the mechanism of the lock since this can cause the problem to get worse It is also recommended that you avoid using lubricants like grease or oil since they could cause the locking mechanism to become sticky Instead, you should opt for light machine oil or graphite as they are safer and won't harm the uPVC A uPVC barrel for doors can be quite difficult to remove once it has been installed, so be aware of what you are doing before you begin If you're not familiar with this kind of repair, you should seek the assistance of locksmiths to ensure the work is done correctly This will help you save time as they will complete the job quickly and efficiently The first step is to unbolt the screw that holds the barrel lock in place This screw should be a different colour than the other screws on the door It's located near the lock faceplate, on the inside of the Once this is removed, you can then slide the barrel lock out Once the lock is out you can then take off the handle and replace it with the new one It is important to know that a locked uPVC can be shut and opened without the handle The uPVC comes with an inbuilt security system known as multipoint locking This system consists of two hooks at the top and bottom, along with the deadbolt or latch in the middle This makes a very sturdy and secure door If you're unable to open your uPVC doors, it's most likely that the locking cylinder is malfunctioning A uPVC door lock is designed to be fitted with a key, so is not as easy to break or move as other locks You can try fixing the cylinder by yourself, however it is recommended to hire an expert locksmith if you're not experienced in this type of repair Removal of the Cylinder The cylinder, also known as the barrel, is a tiny component in the handle of the handle of a uPVC door that allows you to lock and unlock the door Pin-based technology is employed and has been used for a number of years However the criminals are now targeting it to increase the likelihood of gaining entry You can increase the security of your home by replacing the cylinder To take the handle off first, loosen the screws holding it in place with a Philips-head driver Save the screws so that you are able to reattach the handle when the job is done Find the hole that holds the handle to the trim Find a paper clip or other pin that can be straightened, and then put into the hole As you rotate the handle, apply pressure to the pin until it releases it Once it is released, you can pull the handle toward you to pull the latch inside the cylinder Once you have loosened the old cylinder, it is possible to remove it manually Be careful not to damage threads on either side of the cylinder, or the cam that is in the middle If the cylinder does not slip out easily, the handle furniture or locking mechanism could be pinching it It will have to be released so that it is able to slide out If you're ready to replace the cylinder, you should look for one that is rated by an independent testing agency to meet the minimum standards for anti-snap as well as anti-bump protection There are several different grades of locks on the market, and it is crucial to understand your requirements before you begin to select the replacement Bring your old cylinder to the store, if you can, to ensure that you're buying a replacement that matches There are approximately 25 different sizes of lock cylinders available, so it is essential to measure yours precisely Reinstalling the Cylinder You may have to replace your locks if they're not functioning properly This can be done for a number of reasons, including improving security or ensuring that you meet the insurance requirements It may also be necessary to change your lock if you've lost keys or moved into a new home Whatever the reason, changing your uPVC door lock isn't a difficult task and can be done by most people with a bit of help First, ensure that the door is propped or secured so that it does not close during the process Remove the screws that hold the handle by using a screwdriver Be cautious not to remove the screws too quickly, as this could cause small pieces to fly off and get lost Slide out the interior and exterior handles at the same time after removing the screws It's a bit tricky but do not force anything If you do, it could break the handles, and it could also cause damage to the mechanism of the handle After the handles have been removed After that, locate the cylinder fixing screw on the edge of the door This is usually a large screw, which is on the lower edge of cylinder It should have a different color to the other screws and easy to identify Twist the screw to loosen it and then remove it After removing the screw, you should be able to see the cylinder in its socket Insert your key and turn it in both left and right positions This will unlock the cylinder Once you have it unlocked, you can use a gentle pulling to take the cylinder out of its socket After you've removed the old cylinder, place the new one into its socket It should be able to go in without difficulty If you're struggling, try wiggling and tugging again If you're not able to get the cylinder in, consider replacing the lock completely If you are replacing a euro cylinder make sure you purchase one with anti-snap and/or anti-bump protection These features will improve your home's security and make it harder for criminals to bypass the lock Reinstalling the Handle There are a few reasons your uPVC handle might not be functioning correctly Sometimes it's a simple case of wear and tear but sometimes the problem is more severe It could be that the cylinder for the lock is defective and can't be repaired, in which case it's time to replace it with a brand new one https//wwwrepairmywindowsanddoorscouk/altrincham-window-lock-repairs-near-me/ to do is remove the old handle from the door This isn't difficult to do and usually you can do it by removing the two screws that hold the handle in place using a screwdriver Once the screws are removed there should be nothing to hold the handle to the door it should be able to pull away with a minimum of effort It's a good idea to clean the spindle and the back plate after taking off the handle This will ensure that there's no grime or dirt to cause issues for the new handle You should also wash the handle with a soft, clean cloth to get rid of any dust or dirt that could hinder its performance Before you reinstall the new handle, take the time to look at how it fits on the door, in the majority of cases, the hook plate and roller face plate fit into recesses in the centre lock case, so that there isn't any gap between them If the handles aren't fitted properly it can cause lots of pressure on the centre lock case, and there is a risk that something might break inside Start by slipping the spindle through the hole of the outside handle, then into the hole of the inside handle You may need to tap the spindle with mallet or hammer in order to allow it to slide into Once it is in place, there will be a small bolt of retaining on the outside which you'll need to tighten Line up the holes, and replace the bolt that holds it in place