Peugeot 3008 Key Fob Problems The mid-sized SUV from Peugeot 3008, has lots of positive points It's well-designed, it drives good and has a surprising big boot But is https//wwwg28carkeyscouk/peugeot-car-key-replacements-near-me/ to beat off strong competition in the most crowded area of the market If your Peugeot key fob is not working, it may have been exposed to clean tap water or soapy water It is possible to take off the battery and clean it using electronic cleaner or isopropyl alcohol Dead coin battery Peugeot key fobs are powered by a coin-sized battery This power is used to operate the remote locking system, as well as other functions The battery is a bit dated and wears out after years of usage An easy way to determine whether the battery is faulty is by performing an examination of voltage Multimeters are used to measure the voltage between the plus and minus poles of the battery The results of this test will indicate whether the battery is dead or not The receiver module may be the reason behind the key fobs that you have not been able to use after you've used your Peugeot 3008 for a long period of time The receiver module is responsible for capturing radio frequency signals from the key fobs and sending signals to the car's systems If the receiver module malfunctions and not functioning properly, it won't be able send commands to the other modules in the vehicle Another common reason for a key fob that is not working is moisture or sweat on the circuit board This can result in short circuits which drain the battery and can also cause the device to lose the remote locking feature of the key fob If this is the case then you must take your key fob in to an expert on chip level to repair it Water damage Whether you dropped your key fob in the pool, tossed it in the washing machine or even left it in the rain for too long, water damage can be a major issue Water is a great conductor and can easily cause short circuits on the circuit board It can also cause corrosion of the traces of metal and other components on the key fob A circuit board that is wet can also cause the battery to discharge its charge If you have an extra key fob, use it to lock or unlock your Peugeot 3008 to eliminate the possibility that a dead battery is the cause of the problem Another issue that may prevent your key fob from functioning correctly is interference signals that interfere with the signal transmitted to the receiver module These interference signals are caused by many sources which include radio transmitters located in the area If you hear sloshing noises emanating from your Peugeot 3008 when you drive, this is likely due to a clogged condensate drain of the evaporator You can determine this by locating the drain holes underneath your door and blowing compressed air in the drain holes You can also use flexible wire to wiggle the drain holes and wash away any dirt that may have collected there The sloshing sounds can also indicate that there are air pockets in the coolant system Receiver module that is defective The receiver module of the Peugeot 3008 key fob is responsible for sending the remote keyless system signal from the key fob to the car's receiver If this module is damaged, it will hinder the car's ability to recognize the key fob Other reasons that could cause this problem include an unresponsive battery or water damage, as well as interference from electronic devices that operate on the same frequency the key fob In these instances, a message stating "card not detected" may be displayed on the display There are many ways to solve this issue Try replacing the battery or reprogram the key fob You can also use a spare key to start the car However, if the fob doesn't work after all these steps, it might have a chip that's malfunctioning The best method to determine whether the key fob is equipped with a faulty chip is to remove it and clean it with paper towel and rubbing alcohol If the chip is fried it is recommended to purchase an entirely new one FB Series enclosures are designed for use with a key fob They come with a coin battery holder for cell batteries that fits the most common type of key fob batteries These enclosures are customizable using digital printing and CNC-machined cutouts If your key fob was exposed to salted or dirty tap water, it is possible that the chip has become affected by the contamination Faulty keyless entry systems If you get "card not detected", this means that your car is unable to receive the signal from your key fob This can be due to a variety of causes, including an insufficient or dead battery The issue is often resolved by pressing the start button on the key fob In some instances, however, you may need to take the key fob to a Peugeot dealership for additional repairs Examining the battery is the first step to diagnosing the problem with a Peugeot 3008 keyfob which doesn't lock or unlock doors Batteries are often the cause of malfunctioning keys However, there are also other reasons that could be involved These include worn buttons, damage to the receiver module, water issues and signal interference If you've recently experienced the Peugeot key fob exposed to water that is clean it's best to remove the battery and dry the electronic components with paper towel You can also use isopropyl alcohol or cleaning solution to do this If the fob has been exposed to soapy or salty water, it's recommended to replace it If your key fob still doesn't work It can be reset by taking out the battery that is 12 volts for 15 minutes Then connect the negative cable first, then followed by the positive one