Door Hinge Repair Cambridge Door hinges are an insignificant detail that can have a big impact on the performance and look of your doors Replacing your noisy hinges is an inexpensive, quick fix to enhance the appearance of your house One common way to repair door hinges that sound squeaky is to make use of petroleum jelly or bar soap Simply rub the item on the hinges until it's coated Replacement Hinges Hinges are a small component that can cause a large amount of damage if they break or wear out Fortunately, hinges can be replaced without any special tools It is essential to select the proper hinge for your home This will help ensure that your door can be closed and opened easily If your hinges for your door aren't working properly, contact an expert to repair them as soon as is possible A damaged hinge could cause the door to swell or pull away from the frame It is usually due to improper use or an excessive amount of weight Lubricating your hinges is vital to prevent this This will prevent the hinge from rusting, or squeaking and will prolong the life of your doors There are many different kinds of hinges Each has its own advantages and drawbacks The simplest hinge is the butt joint, which is secured to the door by putting a pin on each side This kind of hinge is perfect for doors with light weights as it doesn't need much strength to open and close However, the butt joint is more prone to deterioration than other hinges For doors that are heavier, it's best to choose a continuous piano hinge This type hinge is positioned on the door and runs the entire length of the door which allows it to close and open with ease This style has the advantage of not requiring a center support, and is more stable The storefront door pivot is another typical hinge It allows the door to pivot from only one point on the top or bottom of the door These hinges are usually found in commercial buildings and are difficult to repair when damaged Professionals can assist you in installing an entirely new pivot or replacing the old one The price of hinges can vary depending on the kind Loose Hinges When hinges are loose, they will cause the door to hang in a crooked manner and may even start to scrape against the floor, which is frustrating at best In general, loose hinges are a issue which can be easily solved by any homeowner who has the use of a few tools Most of the time, simply tightening hinge screws can fix the issue however in some instances, the screw holes might be worn out and won't stay tight If the screws are damaged, you'll have to drill them out and then plug them with wooden dowels, or glue-coated wooden matches It is important to lubricate and tighten your door hinges frequently to avoid them becoming loose It is also crucial to check for any signs of damage to the hinges If you see any chips or cracks in the metal, it could be a sign that it's time to replace the hinge It is also recommended to replace hinges when they begin to stick or bind as you shut and open the door The most common reason for hinges on doors becoming loose is wear and tear resulting from continuous use, but without proper oiling or tightening This is true especially for doors that are commonly used by children They may hang on handles of doors or even swing on hinges This puts a lot of unnecessary stress on the hinges This can lead to them becoming loose and eventually falling off completely If hinges are loose, you can tighten them up with a screwdriver However, if the hinges are loose for an extended period of time, the constant movement of both the hinge plate and screws will begin to create larger holes where the screws go The screws will cease to be useful when they cannot remain in place To remedy this, dip the bare end the match with a wooden one in regular carpenter glue and tap it a little using a hammer This will push the glue as far into the hole as you can It's likely that you'll have to insert several of these glue-coated matches to fill the hole Rusty Hinges Rust is a common problem for door hinges, especially on older doors It can cause the hinges to look shabby and can cause them to fail and break This can be dangerous to those who use the door It is possible to save a damaged hinge with a bit of effort The first step is removing hinges and cleaning them to eliminate any gunk After the hinges have been cleaned, they can be oiled before being used again In the past hinges of poor quality were made of iron and steel that were prone to be rusty, but modern doors are often constructed from brass or other metal alloys that don't rust as easily Despite this, some people still prefer traditional iron hinges due to their durability and beauty even though they are more susceptible to rust than modern hinges The best method to prevent this is to stop the hinge from becoming rusty It is the easiest way to clean the hinges on a regular basis with steel wool and water, particularly when they are damp If you do it often, rust won't be a problem with your hinges for doors If you want to go further, consider using stainless steel for your hinges As opposed to iron, stainless steel doesn't rust and can provide your home with a more modern aesthetic If you're not able to replace the existing hinges, however the best way to prevent rust is to keep it away from the hinges on your doors by regularly cleaning them and oiling them If you are taking off the hinges, it's best to do it thoroughly so that you can reach all the tiny places to wash off any rust When the hinges are clean you can use an oil-based mixture with vinegar to further lubricate them and help to protect them from corrosion This is an inexpensive and simple solution that is easily accessible in most homes It's a good idea to give it trying before you think about replacing your hinges Doors that won't shut In time, doors become displaced due to the expansion and contraction of wooden frames When this occurs, the door might catch on the edges of the frame, or catch on the latch when you attempt to shut it A little bit of work can often fix these problems If you can tighten the hinges, and correct the misalignment of the door, it is likely to close once more Check the hinges to see whether there are loose screws A loose screw could cause the hinge leaf to move, creating gaps between it and the jamb This could cause the latch not to reach the strike plate's hole, and cause a jammed-up door To fix this, remove one of the hinge screws and slide a strip of cardboard we prefer the backs of old legal pads between the hinge and the door jamb Screw the hinge into place This will increase the gap along the hinge's side, and narrow it down on the latch side, allowing the latch to clear the strike plate If this fixes the problem, repeat the procedure on the remaining hinges If you still have problems you can hammer or shim the strike plate to align it with the hole in the latch If this is the situation then a small amount of paint or wood filler is usually enough to conceal the changes Long-term use or physical damage can also cause the strikeplate to be bent or curved that can cause it to strike the edge but not go enough to keep the door shut To test for this, apply lipstick to the latch and stick the strip of masking tape to the strike plate Close the door and open it https//wwwrepairmywindowsanddoorscouk/cambridge-windowrepair/ will leave a mark on the tape where the latch touches the strike plate hole If the mark is below the hole, then the latch should be moved upwards