Peugeot 3008 Key Fob Problems Peugeot's 3008 SUV, which is mid-sized, has a lot to offer It looks smart, drives well and has a big boot But can it beat against strong competition in the most congested sector of the market If your Peugeot key fob isn't functioning, it may have been exposed to clean tap water or soapy water It is possible to take off the battery and clean it with electronic cleaner or isopropyl alcohol Dead coin battery Peugeot key fobs are powered by a coin-sized battery This power is utilized to operate the remote locking system, as well as other functions The battery has a short lifespan and is susceptible to get worn out after years of usage Voltage testing is an easy method to determine if the battery is defective Multimeters are used to determine the voltage between the plus and minus poles of the battery The results of this test will tell you whether the battery is dead or not The receiver module could be the reason why your key fobs not working after having used your Peugeot 3008 for a prolonged period The receiver module is responsible for receiving radio frequency signals from the key fobs and transferring them to the vehicle's systems If the receiver module has an issue, it will not be able to transmit commands to other modules in the car Moisture or sweat on the circuit board is another common reason for a malfunctioning key fob This can result in short circuits that drain the battery, and can also cause the device to lose the remote locking feature of the key fob If this is the case you must take your key fob in to a specialist in chip level repairs Water damage Water damage can be a problem in the event that you dropped your keyfob in the pool water, washed it, or left it out in the rain Water is a good conductor and can easily short out parts of the circuit board It can also cause rusting of the traces of metal and other components of the key fob A circuit board that is wet could also cause the battery dump its charge If you have a spare key fob, use it to lock or unlock your Peugeot 3008 to rule out the possibility that a dead battery is the root of the problem Another issue that can prevent the key fob from operating properly is interference signals that interfere with the signal that is sent to the receiver module These signals can be caused by many sources, including radio transmitters within the close vicinity If you hear sloshing sounds coming from your Peugeot 3008 when you drive it is most likely due to a blocked condensate drain of the evaporator You can test this by blowing compressed air through the drain holes beneath your door You can also use a flexible metal wire to wiggle drain holes to clean any dirt that has collected Air pockets can also be identified by sloshing sound Faulty receiver module The receiver module on a Peugeot 3008 key fob is responsible to transmit the remote keyless system signal from the key fob to the car's receiver This module could be damaged and stop the car from being able to recognize your key fob Other reasons that could cause this issue are a dead battery or water damage, or interference from electronic devices operating at the same frequency as the key fob In these situations, the car may show a message saying "card not detected" on the display There are many ways to solve this issue You may try replacing the battery, or reprogramming the key fob You can also use a spare key to start the car If the key fob doesn't work after these steps, it may have a chip that's defective It is recommended to remove the chip and clean it using paper towels and rubbing alcohol If the chip has gone bad you need to buy the new one The FB Series enclosures come with the battery holder for coins that can be used with the most commonly used types of key fob batteries The enclosures can be personalized by using digital printing or CNC-machined cutouts If your key fob was exposed to dirty or salty tap water, the chip may be contaminated and requires to be cleaned A malfunctioning keyless entry system If you see the message "card not detected" It signifies that your car can't receive the signal from your key fob This could be due to many reasons like an insufficient or dead battery The issue can be resolved by pressing the start button on the key fob In some cases, however, you may need to take the key fob to an Peugeot dealership for additional repairs Checking the battery is the first step to solving the issue with a Peugeot 3008 keyfob that won't lock or unlock doors Batteries are usually the cause of malfunctioning key fobs However there are https//wwwg28carkeyscouk/peugeot-car-key-replacements-near-me/ that could be involved These include worn buttons water damage, receiver module issues, and signal interference If your Peugeot key fob has been exposed to pure tap water, it's a good idea for you to take the battery off Then dry the electronic components with paper towel You can also use isopropyl alcohol or an appropriate cleaner for this It is best to change the fob after it has been exposed to salt or soapy water If your key fob still doesn't work you can reset it by removing the battery with 12 volts for 15 minutes Connect the negative cable, and then the positive cable